january 2010 ? 2008 fairchild semiconductor corporation www.fairchildsemi.com fan2013b ? rev. 1.0.1 fan2013b ? 2a low-voltage, current-m ode synchronous pwm buck regulator fan2013b ? 2a low-voltage, current-mode synchronous pwm buck regulator features ? 95% efficiency, synchronous operation ? adjustable output voltage from 0.8v to 3.6v ? 4.5v to 5.5v input voltage range ? up to 2a output current ? fixed-frequency 1.2 mhz pwm operation ? soft-start function ? excellent load transient response ? power-good flag ? over-voltage, under-voltage lockout, short- circuit, and thermal shutdown protections ? 3x3mm 6-lead mlp package applications ? hard disk drive ? set-top box ? point-of-load power ? notebook computer ? communications equipment description the fan2013b is a high-efficiency, low-noise, synchronous pulse width modulated (pwm) current- mode dc-dc converter designed for low-voltage applications. it provides up to 2a continuous-load current from the 4.5v to 5.5v input. the output voltage is adjustable over a wide range by means of an external voltage divider. the fan2013b is enabled when the input voltage on the v in pin exceeds the uvlo threshold. a current-mode control loop with a fast transient response ensures excellent line and load regulation. the fixed 1.2mhz switching frequency enables designers to choose a small, inexpensive external inductor and capacitor. filtering can be accomplished with small components, reducing space and cost. protection features include input under-voltage lockout, short-circuit protection, and thermal shutdown. soft- start limits inrush current during start-up conditions. the device is available in a 3x3mm 6-lead mlp. typical application figure 1. typical application ordering information part number output voltage package eco status packing method FAN2013BMPX 0.8v to 3.6v 3x3mm 6-lead molded leadless package (mlp) green tape and reel for fairchild?s definition of eco status, please visit: http://www.fairchildsemi.com/com pany/green/rohs_green.html .
? 2008 fairchild semiconductor corporation www.fairchildsemi.com fan2013b ? rev. 1.0.1 2 fan2013b ? 2a low-voltage, current-m ode synchronous pwm buck regulator pin assignments figure 2. pin assignments (top view) pin definitions pin # name description p1 agnd analog ground . p1 must be soldered to the pcb ground. 1 fb feedback input . adjustable voltage option; connect this pin to the resistor divider. 2 pgnd power ground . this pin is connected to the internal mosfet switches. this pin must be externally connected to agnd. 3 sw switching node . this pin is connected to t he internal mosfet switches. 4 pvin supply voltage input . this pin is connected to t he internal mosfet switches. 5 vin supply voltage input . 6 pg open drain power good .
? 2008 fairchild semiconductor corporation www.fairchildsemi.com fan2013b ? rev. 1.0.1 3 fan2013b ? 2a low-voltage, current-m ode synchronous pwm buck regulator absolute maximum ratings stresses exceeding the absolute maximum ratings may dam age the device. the device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. in addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. the absolute maximum ratings are stress ratings only. symbol parameter min. max. unit v in supply voltage -0.3 7.0 v input voltage on pvin and any other pin -0.3 v in v jc thermal resistance, junction-to-tab (1) 8 c/w t l lead soldering temperature (10 seconds) +260 c t stg storage temperature -65 +150 c t j junction temperature -40 +150 c esd electrostatic discharge protection level (2) hbm 3.5 kv cdm 2.0 notes: 1. junction-to-ambient thermal resistance, ja , is a strong function of pcb material, board thickness, thickness and number of copper planes, number of via used, diameter of via used, avail able copper surface, and attached heat sink characteristics. 2. using mil std. 883e, method 3015.7 (human body model) and eia/jesd22c101-a (charged device model). recommended operating conditions the recommended operating conditions table defines the conditions for actual device operation. recommended operating conditions are specified to ens ure optimal performance to the datasheet specifications. fairchild does not recommend exceeding them or designing to absolute maximum ratings. symbols parameter min. typ. max. unit v in supply voltage range 4.5 5.5 v v out output voltage range, adjustable version 0.8 3.6 v i out output current 2.0 a l inductor (3) 2.2 h c in input capacitor (3) 10 20 f c out output capacitor (3) 20 40 f t a operating ambient temperature range -40 +85 c note: 3. refer to the applications section for details .
? 2008 fairchild semiconductor corporation www.fairchildsemi.com fan2013b ? rev. 1.0.1 4 fan2013b ? 2a low-voltage, current-m ode synchronous pwm buck regulator electrical characteristics v in = 4.5v to 5.5v, v out = 1.2v, i out = 200ma, c in = 10f, c out = 40f, l = 2.2h, t a = -40c to +85c, unless otherwise noted. typical values are at t a = 25c. symbol parameter conditions min. typ. max. units v in input voltage 4.5 5.5 v i q quiescent current i out = 0ma 10 16 ma v uvlo uvlo threshold v in rising 3.4 3.7 4.0 v hysteresis 150 mv r on_pmos pmos on resistance v in = v gs = 5v 90 m r on_nmos nmos on resistance v in = v gs = 5v 90 m i limit p-channel current limit 4.5v < v in < 5.5v 2.8 3.5 4.2 a over-temperature protection rising temperature 150 c hysteresis 20 c f sw switching frequency 1000 1200 1400 khz r line line regulation v in = 4.5 to 5.5v, i out = 100ma 0.16 %/v r load load regulation 0ma i out 2000ma 0.3 0.6 % v out output voltage during load transition (4) i out from 1500ma to 100ma, c out = 60f 5 % i out from 100ma to 1500ma, c out = 60f -5 % i leak reverse leakage current into pin sw v in = open, en = gnd, v sw = 5.5v 0.1 1.0 a v ref reference voltage 0.8 v v out output voltage accuracy v in = 4.5 to 5.5v, 0ma i out 2000ma, t a = 0c to +85c -2 2 % v in = 4.5 to 5.5v, 0ma i out 2000ma, t a = -40c to +85c -3 3 % v pg power good output threshold and hysteresis fb voltage rising 0.9 x v out v hysteresis 1 % t pg power good output delay 100 s v pg_low power good voltage low i sink =6ma, open-drain output 0.4 v v ovp over-voltage protection threshold and hysteresis fb voltage rising 1.07 x v out v hysteresis 2 % note: 4. please refer to the load transient res ponse test waveform shown in figure 3. 0.6 time (ms) i load (ma) s s 0 4.6 100 1500 t r = 100ns t f = 100ns s s s s s s figure 3. load transient response test waveform
? 2008 fairchild semiconductor corporation www.fairchildsemi.com fan2013b ? rev. 1.0.1 5 fan2013b ? 2a low-voltage, current-m ode synchronous pwm buck regulator typical performance characteristics t a = 25c, c in = 10f, c out = 40f, l = 2.2h, v in = 5v, v out = 1.2v, unless otherwise noted. figure 4. startup with 100ma resistive load figure 5. startup with 2a resistive load i l v out i load figure 6. load transient response, 1.2v out (100ma to 1500ma, 20s/div) figure 7. load transient response, 3.3v out v (100ma to 1500ma, 20s/div) 1.198 1.199 1.2 1.201 1.202 1.203 00.511.52 load current(ma) output voltage(v) 5vin 4.5vin 5.5vin figure 8. output voltage regulation figure 9. power efficiency
? 2008 fairchild semiconductor corporation www.fairchildsemi.com fan2013b ? rev. 1.0.1 6 fan2013b ? 2a low-voltage, current-m ode synchronous pwm buck regulator block diagram figure 10. block diagram detailed operation description the fan2013b is a step-down pulse-width modulated (pwm) current mode converter with a fixed switching frequency of 1.2mhz. at the rising edge of each clock cycle, the p-channel transistor is turned on until the pwm comparator trips or t he current limit is reached. during the on time, the inductor current ramps up and is monitored by the internal current-mode control loop. after a minimum dead time, the n-channel transistor is turned on and the inductor current ramps down. as the clock cycle is completed, the n-channel switch is turned off and the next clock cycle starts. the duty cycle is given by the ratio of output voltage and input voltage. the converter runs at minimum duty cycle when the output voltage is at minimum and input voltage is at maximum. the duty cycle increases proportionally as the input voltage approaches the output voltage. uvlo and soft start the internal voltage reference, v ref , and the ic remain reset until v in reaches the uvlo threshold. the fan2013b has an internal soft-start circuit that limits the inrush current dur ing start-up. this prevents possible voltage drops of the input voltage and eliminates the output voltage overshoot. the soft-start is implemented as a digital circuit, increasing the switch current in four steps to the p-channel current limit. typical start-up time for a 40f output capacitor with a load current of 2.0a is 800s. output over-voltage protection when output voltage, v out , reaches approximately 7% above the nominal value, the device turns off the p- channel switch and turns on part of the n-channel transistor with a built-in current limit of about 400ma. when v out reaches the hysteresis of about 2%, the device starts switching normally in closed loop. if output voltage is pulled up by an external voltage source with a current limit higher than typical 400ma, the output voltage stays up at the external voltage source level. the over-voltage protection is designed to limit the output voltage excursion in case of a transient response from full load to a minimum load. output short-circuit protection the switch peak current is limited cycle by cycle to a typical value of 3.5a. in the event of an output voltage short circuit, the device operates with a frequency of 400khz and minimum duty cycle, making the average typical input current 0.45a. thermal shutdown when the die temperature exceeds 150c, a reset occurs and remains in effect until the die cools to 130c, when the circuit is allowed to re-initiate a soft- start cycle..
? 2008 fairchild semiconductor corporation www.fairchildsemi.com fan2013b ? rev. 1.0.1 7 fan2013b ? 2a low-voltage, current-m ode synchronous pwm buck regulator applications information setting the output voltage the internal voltage reference is 0.8v. the output is divided down by a voltage divider, r1 and r2 to the fb pin. the output voltage is: v out v ref 1 r 1 r 2 -- -- - - + = (2) according to this equation, assuming desired output voltage of 1.2v, and given r2 = 10k as the recommended resistance for any output voltage setting, the calculated value of r1 is 5k . inductor selection the inductor parameters directly related to device performance are saturation current and dc resistance. the fan2013b operates with a typical inductor value of 2.2h. the lower the dc resistance, the higher the efficiency. for saturation current, the inductor should be rated higher than the maximum load current, plus half of the inductor ripple current, calculated by: ? () ? lf ------------------------------------------ - = (3) where: i l = inductor ripple current f = switching frequency l = inductor value recommended inductors are listed in table1. table 1. recommended inductors inductor value vendor part number 2.2h coiltronics sd25 2r2 2.2h murata lqh66sn2r2m03l capacitor selection for best performance, a low- esr input capacitor is required. a ceramic capacitor of at least 10f, placed as close to the v in and agnd pins as possible is recommended. the output capacitor determines the output ripple and the transient response. a minimum of 20f output capacitor is required for the fan2013b to operate in stable conditions. table 2. recommended capacitors capacitor value vendor part number 10f taiyo yuden jmk212bj106mg jmk316bj106kl tdk c2012x5roj106k c3216x5roj106m murata grm32er61c106k pcb layout recommendations the inherently high peak currents and switching frequency of power supplies require a careful pcb layout design. for best results, use wide traces for high- current paths and place the input capacitor, the inductor, and the output capacitor as close as possible to the integrated circuit terminals. to minimize voltage stress to the device resulting from ever-present switching spikes, use an input bypass capacitor with low esr. note that the peak amplitude of the switching spikes depends upon the load current; the higher the load current, the higher the switching spikes. the resistor divider that sets the output voltage should be routed away from the inductor to avoid rf coupling. the ground plane at the bottom side of the pcb acts as an electromagnetic shield to reduce emi. the recommended pcb layout is shown below in figure 11. figure 11. recommended pcb layout
? 2008 fairchild semiconductor corporation www.fairchildsemi.com fan2013b ? rev. 1.0.1 8 fan2013b ? 2a low-voltage, current-m ode synchronous pwm buck regulator physical dimensions figure 12. 3x3mm 6-lead molded leadless package (mlp) package drawings are provided as a service to customers considering fairchild components. drawings may change in any manner without notice. please note the revision and/or date on the drawing and contact a fairchild semiconductor representative to ver ify or obtain the most recent revision. package specifications do not expand the terms of fairchild?s worldwide terms and condition s, specifically the warranty therein, which covers fairchild products. always visit fairchild semiconductor?s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/ .
? 2008 fairchild semiconductor corporation www.fairchildsemi.com fan2013b ? rev. 1.0.1 9 fan2013b ? 2a low-voltage, current-m ode synchronous pwm buck regulator
|
